Having a Geek Bar that doesn’t stop hitting is definitely one of the more disconcerting things that can happen to you as a vaper. When this happens, you may notice that you can take a puff and move the device away from your mouth, and it continues to hiss and crackle even though you’re no longer using it.
So, what does it mean if you have a Geek Bar that doesn’t turn off after you hit it? Is it dangerous, and how can you fix it? In this guide, we’ll explain exactly what you need to do.
Turn Your Geek Bar Off
If you have a Geek Bar that hits on its own, you should start by turning the device off. Most Geek Bar models have switches on the bottom that you use to control their power levels. If you move the switch to the “Close” position, the device will turn off immediately.
After several seconds, turn the device back on and see what happens. Does it resume hitting on its own?
- If not, it’s possible that you were dealing with a transient firmware issue. Continue vaping and see if the problem returns.
- If it does resume hitting on its own, turn your Geek Bar off while you perform further troubleshooting.
Blow Through the Mouthpiece
If turning your Geek Bar off and back on doesn’t stop it from hitting on its own, the next most likely cause for the issue is that the device’s airflow sensor is stuck in the “on” position. The airflow sensor for a disposable vape is a tiny and inexpensive component. It’s usually a small membrane that flexes when air moves through the device, causing the circuit to activate. The sensor can stick in place if e-liquid gets on it, and that’s the most common reason why a Geek Bar doesn’t stop hitting.
To free the sensor, blow hard through the mouthpiece while your Geek Bar is turned off. This pushes the membrane in the outward direction, which should free it.
Turn the Geek Bar back on and see what happens. Does it resume hitting on its own?
- If not, you can continue using your Geek Bar normally. Understand that if the airflow sensor still has e-liquid on it, it could get stuck again. If that happens, you’ll need to blow through the mouthpiece again to fix it.
- If it does resume hitting on its own, turn your Geek Bar off and continue to the next section for another possible fix.
Tap the Geek Bar Gently
Blowing through the mouthpiece usually fixes a Geek Bar with a stuck airflow sensor, but there is another possible solution if that doesn’t work: You can tap the device firmly a few times with your finger while holding it with your other hand. Don’t throw the device or slam it against something, which can potentially cause battery damage.
Turn the Geek Bar back on and see what happens. Does it resume hitting on its own?
- If not, you can continue using your Geek Bar normally. You may need to tap it or blow through it if the problem continues happening, though, because the airflow sensor may get stuck again.
- If it does resume hitting on its own, turn your Geek Bar off and prepare it for recycling.
Recycle the Geek Bar if You Can’t Fix It
If you’re unable to get your Geek Bar to stop hitting on its own by following all of the recommendations in this article, the device is most likely unfixable through standard means. Either the puff sensor is badly stuck, or the device has been damaged somehow. It’s also possible that you have a fake Geek Bar, which we’ll discuss at the end of the article. Leave the device turned off and recycle it according to your local waste management guidelines.
How to Prevent a Geek Bar from Hitting on Its Own
As we explained above, a Geek Bar usually starts hitting on its own because e-liquid has gotten on the airflow sensor. Although it’s valuable to know how to fix that problem, it’s even better if you can prevent it from happening in the first place. These three tips can help.
- Use minimal air pressure when inhaling through your Geek Bar. If you puff too hard, you can pull e-liquid out of the device’s internal container.
- Store your Geek Bar upright as much as possible. Keeping the device on its side for extended periods can potentially cause e-liquid to leak out of the container.
- Keep your Geek Bar out of direct sunlight and avoid other situations that can cause the device’s temperature to become elevated. E-liquid becomes less viscous when it’s warm, which can increase the chance of a leak – especially if the device is on its side.
The Importance of Buying Authentic Geek Bars
When you look for Geek Bars for sale, getting authentic hardware is absolutely crucial because Geek Bar is today’s most popular vape brand. That means it’s also the most counterfeited brand.
One of the reasons why avoiding fake Geek Bars is so important is because unscrupulous manufacturers are very likely to cut corners when building counterfeit devices. A puff sensor is exactly the kind of component that the manufacturer might replace with a cheap, sub-par alternative – and in that case, you could end up with a Geek Bar that won’t stop hitting even if you’re doing everything right.
Here are the easiest ways to avoid buying fake Geek Bars.
- Always buy from a trusted vape shop. Vape shops should always get their inventory from official sources. Convenience stores and shady social media sellers might not.
- Always use the scratch-off section on the box to reveal a device’s authenticity code before unboxing the device. Visit the official Geek Bar website and enter the code to confirm that the device is authentic.
- Check the device carefully before you begin using it. If something doesn’t look right – or the flavor doesn’t seem correct – you should return the device to the point of purchase because it’s not worth the risk.